Advertisement
parts2clean, 24 - 26 October 2017
Homepage>Exhibitors & Products >Turbocharger housings cleaning machine

Turbocharger housings cleaning machine

Clean castings - compact machine - energy-saving operation

Piller Entgrattechnik

Exhibitor details
Logo Turbocharger housings cleaning machine

Exhibition stand

Hall 3, Stand B43
Open Exhibition Grounds map

Contact(s)
Mr. Dr. Matthias Wadle
Sales Manager
Send E-mail
Fax: +49 7152 99770 26

Product description

Perfect cleaning of machined turbocharger housings

High cleaning quality and short cycle times in combination with low space and energy requirements, and this for the lowest possible investment. In cycle times under 60 seconds the system removes dirt and clamping chips from the workpieces in several zones and finally dries the parts. Maximum 600 microns particle size after cleaning was the challenging quality specification.


Maximum processing time and machine flexibility

On a specially designed cleaning pallet, the turbochargers are very quickly fed through the machine via chain drive. In the individual process zones, the cleaning platforms are decoupled from the chain and are individually movable. This allows optimal alignment process to spraying technique. Thanks to the very quick part transport, the available processing time in each zone can be better exploited. This construction also allows flexibility for different type turbocharger, which can be cleaned in the washing machine. The spraying technique is divided into three areas. Two of them work with low pressure and a chamber is equipped with a high-pressure cleaning system. This one works with pressures below 200 bar and removes reliably all clamping chips from the workpieces.

Energy efficiency all around

Each process zone has been constructed so that the water quantity and the pressure level have been very reduced to the real requirements. Much attention was paid also to the entire air flow inside and outside the machine.
With a reduced quantity of water, divided into two baths, you can expect manageable energy costs in daily operation. Bag filters perform the filtration and the bath heating is electric. In the drying zone, optimized air quantity exhaust technique and a vacuum chamber are used. In the drying zone, optimized air quantity exhaust technique and a vacuum chamber are used.

Product website

All products offered by this exhibitor

VectorJet IV

NC water jet centre based on a dual-chamber system for the alternating processing of camshafts. In this particular case, processing is carried out using cutting oil, but the machine can easily be adapted for use with water. The machine can be loaded manually and is suitable for fully automated, interlinked ...read more

RoboJet Series

Clean, fast and effectiveread more

VectorJet III

Large horizontal processing centre with high-speed swivel table and bulkhead. The swivel table is fitted with two rotary plates (B-axes), separated by means of a dividing wall, thus creating separate loading and processing chambers. Processing can be performed along up to three horizontal axes using ...read more

Part-specific machines

Part-specific deburring, chip removal, sand removal and cleaningread more

Turbocharger housings cleaning machine

Perfect cleaning of machined turbocharger housings High cleaning quality and short cycle times in combination with low space and energy requirements, and this for the lowest possible investment. In cycle times under 60 seconds the system removes dirt and clamping chips from the workpieces in several ...read more

Contract deburring and cleaning services

Subcontracting cleaning and deburring of your parts: a precision service provided by Piller For small quantities, tests for bridging delivery periods or low volume productions and in connection with ramp-ups, we are the service provider with expertise. We provide 100% precision deburring in 24 hours ...read more

Piller CleanCheck

In the last few years, the requirements for parts cleanliness have become increasingly tough and they will continue to become more demanding in the future. Today, the residual contamination analysis is a process separate from the production process. The tested parts with not OK results require time ...read more

Vacuum dryer

The vacuum dryer is also available as an standalone component. Equipped with state-of-the-art vacuum pumps, it gives consistent optimal drying results for your components. It can be loaded and unloaded manually or automatically. It is also available as a front loader and as a continuous feed system. ...read more

High-pressure deburring systems

Vertical processing centre featuring rotary plate, B-axis -Flexible processing with the help of a pallet system for automated workpiece infeed and various different workpieces -Six-sided processing possible -Short cycle timesread more

Stored items

0

Server communication error: Item could not be saved.